Honda Fury Forums: banner
1 - 11 of 11 Posts

·
Registered
Joined
·
1,032 Posts
Discussion Starter · #1 ·
Another option has become available!
mortons


You tube link of some black taped infernos'. My Favorite look so far!
YouTube - New Pipes on Fury

Anyone have any knowledge of this company and what kind of quality they produce?
 

·
Registered
Joined
·
1,120 Posts
The Mortons have been out for about a month now. At least one member here has them on their fury. They look good. The bike I have in mind has chrome pipes that are wrapped in black heat tape. From reading his post, I remember they ground down a bit from road contact when the bike was leaned over far.
 

·
Registered
Joined
·
100 Posts
Yeah, that's my bike. I posted another link with a longer clip but here is the link again. The pipes are really nice sounding. A nice deep sound and really loud when you open them up. I have scraped them pretty good, but do ride rather aggressively up the canyons. I have completely scraped off the left peg and am grinding down the foot rest itself now. I take it a little easier on the right due to the pipes though.

YouTube - Morton's down and out pipes on Honda Fury
 

·
Premium Member
Joined
·
749 Posts
Yeah, that's my bike. I posted another link with a longer clip but here is the link again. The pipes are really nice sounding. A nice deep sound and really loud when you open them up. I have scraped them pretty good, but do ride rather aggressively up the canyons. I have completely scraped off the left peg and am grinding down the foot rest itself now. I take it a little easier on the right due to the pipes though.

YouTube - Morton's down and out pipes on Honda Fury
it says on there site "These pipes fit the new Honda Fury. Power Cones are recommended to ensure proper backpressure. A fuel processor is required to reset your carb." what have you done?
 

·
Registered
Joined
·
100 Posts
it says on there site "These pipes fit the new Honda Fury. Power Cones are recommended to ensure proper backpressure. A fuel processor is required to reset your carb." what have you done?
I think they always include the cones with the pipes, they are pretty cheap. Other than that I installed a Dobeck Techlusion fuel controller that has worked out pretty well for me.
 

·
Registered
Joined
·
1,120 Posts
I think they always include the cones with the pipes, they are pretty cheap. Other than that I installed a Dobeck Techlusion fuel controller that has worked out pretty well for me.
Good info!!!
 

·
Registered
Joined
·
39 Posts
Mortons, makes a good quality product. They have been fabricating custom parts for many years. Their website is mortons sample they have been a dealer with RC a long while. I have some personal friends that have used their products and are very pleased with the quality. Just wanted to put in my 2 cents.
 

·
Registered
Joined
·
724 Posts
Another option has become available!
mortons


You tube link of some black taped infernos'. My Favorite look so far!
YouTube - New Pipes on Fury

Anyone have any knowledge of this company and what kind of quality they produce?
I ordered mine last week. I will post pics and a review when I get these suckers on.


If you can't fix it with a hammer, it's an electrical problem.
 

·
Registered
Joined
·
724 Posts
I'd like to know the same thing as TXNurse, getting my Fury tomorrow and this one of the first things im looking at doing.
I have been running mine without a fuel management system for 2 weeks now. She definitely runs a little hot, but I will be putting one on shortly. I did feel a nice difference as far as power with these pipes, from what I hear the fuel controller will make it run even better & cooler. I rarely have a backfire, but the burbeling has to go, I believe that the PAIRS system(on another thread here)is to blame for that, which I will be removing soon.
 
1 - 11 of 11 Posts
Top